I_A_RFC2407_4_6_2_1 - [Initiator Test] Identification Payload Format check
End-Node
I_A_RFC2407_4_6_2_1.seq [-tooloption ...] -pkt I_A_RFC2407_4_6_2_1.def -tooloption : v6eval tool option
See also ike_common.def and ike_ipsec.def and ike_addr.def and ike_pkt_ph1_recv.def and ike_pkt_ph2_recv.def
HOST-2(TN):responder
|3ffe:501:ffff:101::11
|
Net-y --+--------+------------------------ 3ffe:501:ffff:101::/64
|
|
ROUTER-1(TN)
|3ffe:501:ffff:100::11
|
Net-z --+--------+------------------------ 3ffe:501:ffff:100::/64
|
|3ffe:501:ffff:100:XXXX
NUT:initiator
XXXX: EUI64 address
Verification Points
ID Payload Format
Next Payload field
Place the value of the Next Payload in the Next Payload field.
RESERVED Fields
All RESERVED fields in the ISAKMP protocol MUST be set to zero (0).
Place the value zero (0) in the RESERVED field.
Payload Length field
Place the length (in octets) of the payload in the Payload Length field.
Identification Type field
Value describing the identity information found in the Identification
Data field.
(In this test, this field is set as 5(ID_IPV6_ADDR).)
Protocol ID field
Value specifying an associated IP protocol ID (e.g. UDP/TCP)
Port ID field
Value specifying an associated port.
Identification Data field
Value, as indicated by the Identification Type.
(In this test, this value is NUT IPv6 address.)
During Phase I negotiations, the ID port and protocol fields MUST
be set to zero or to UDP port 500.
Configuration
Initiator and Responder IKE parameter
At least, following parameter must be included in proposal.
| Machine |
Src |
Dest |
Phase I |
Phase II |
| Ex mode |
Key Value |
Enc Alg |
Hash Alg |
Auth Method |
DH Group |
PH1 Lt |
IDx |
Proto ID |
Trans ID |
Mode |
Auth Alg |
PH2 Lt |
Upper |
| NUT |
NUT addr |
HOST-2 addr |
Aggressive |
IKE-TEST |
3DES |
SHA |
pre-shared key |
2 |
8 Hour |
NUT addr |
PROTO_IPSEC_ESP |
ESP_3DES |
Transport |
HMAC-SHA |
8 Hour |
any |
| HOST-2 |
HOST-2 addr |
NUT addr |
Aggressive |
IKE-TEST |
3DES |
SHA |
pre-shared key |
2 |
8 Hour |
HOST-2 addr |
PROTO_IPSEC_ESP |
ESP_3DES |
Transport |
HMAC-SHA |
8 Hour |
any |
*Ex Mode = Exchange mode
*IDx = identity payload(FQDN or user FQDN can also be chosen as IDx)
*Enc Alg = IKE Encryption Algorithm
*Hash Alg = IKE Authentication Algorithm
*Key Value = pre-shared key value
*PH1 Lt = Phase-1 Lifetime
*PH2 Lt = Phase-2 Lifetime
*Proto ID = Protocol Identifier
*Trans ID = Transform Identifier
*Mode = Encapsulation Mode
*Auth Alg = Authentication Algorithm
*Auth Method = Authentication Method
*DH Group = Diffie-Hellman Group
*Upper = Upper Layer Protocol
*NUT addr = NUT address
*HOST-2 addr = HOST-2 address
Pre-Sequence
In order to start the negotiation of IKE,
NUT transmits Echo Request to TN(HOST-2).
This test check is following.
AGGRESSIVE EXCHANGE
# Initiator(NUT) Direction Responder(TN)
(1) HDR; SA, KE, Ni, IDii ========>
Judgement (Check *1)
1. Receive the first message from NUT
In the first message (1), the initiator generates a proposal it
considers adequate to protect traffic for the given situation. The
Security Association, Proposal, and Transform payloads are included
in the Security Association payload (for notation purposes).
Keying material used to arrive at a common shared secret and random
information which is used to guarantee liveness and protect against
replay attacks are also transmitted. Additionally, the initiator
transmits identification information.
The first message's Identification Payload Format must be base
on description of RFC(see above Verification Points).
And must conform to above Configuration.
Clean up SAD and SPD
RFC2407
4.6.2 Identification Payload Content
The Identification Payload is used to identify the initiator of the
Security Association. The identity of the initiator SHOULD be used
by the responder to determine the correct host system security policy
requirement for the association. For example, a host might choose to
require authentication and integrity without confidentiality (AH)
from a certain set of IP addresses and full authentication with
confidentiality (ESP) from another range of IP addresses. The
Identification Payload provides information that can be used by the
responder to make this decision.
During Phase I negotiations, the ID port and protocol fields MUST be
set to zero or to UDP port 500. If an implementation receives any
other values, this MUST be treated as an error and the security
association setup MUST be aborted. This event SHOULD be auditable.
The following diagram illustrates the content of the Identification
Payload.
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
! Next Payload ! RESERVED ! Payload Length !
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
! ID Type ! Protocol ID ! Port !
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ Identification Data ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(omit)
o Next Payload (1 octet) - Identifier for the payload type of
the next payload in the message. If the current payload is the
last in the message, this field will be zero (0).
o RESERVED (1 octet) - Unused, must be zero (0).
o Payload Length (2 octets) - Length, in octets, of the
identification data, including the generic header.
o Identification Type (1 octet) - Value describing the identity
information found in the Identification Data field.
o Protocol ID (1 octet) - Value specifying an associated IP
protocol ID (e.g. UDP/TCP). A value of zero means that the
Protocol ID field should be ignored.
o Port (2 octets) - Value specifying an associated port. A value
of zero means that the Port field should be ignored.
o Identification Data (variable length) - Value, as indicated by
the Identification Type.
(omit)
RFC2408
3.8 Identification Payload
(omit)
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
! Next Payload ! RESERVED ! Payload Length !
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
! ID Type ! DOI Specific ID Data !
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
! !
~ Identification Data ~
! !
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(omit)
o DOI Specific ID Data (3 octets) - Contains DOI specific
Identification data. If unused, then this field MUST be set to
0.
(omit)
RFC2408
5.3 Generic Payload Header Processing
When creating any of the ISAKMP Payloads described in sections 3.4
through 3.15 a Generic Payload Header is placed at the beginning of
these payloads. When creating the Generic Payload Header, the
transmitting entity (initiator or responder) MUST do the following:
1. Place the value of the Next Payload in the Next Payload field.
These values are described in section 3.1.
2. Place the value zero (0) in the RESERVED field.
3. Place the length (in octets) of the payload in the Payload Length
field.
4. Construct the payloads as defined in the remainder of this
section.
(omit)
5.8 Identification Payload Processing
When creating an Identification Payload, the transmitting entity
(initiator or responder) MUST do the following:
1. Determine the Identification information to be used as defined by
the DOI (and possibly the situation).
2. Determine the usage of the Identification Data field as defined
by the DOI.
3. Construct an Identification payload.
4. Transmit the message to the receiving entity as described in
section 5.1.
(omit)
perldoc V6evalTool
IKE.html IKE Test Common Utility