R_RFC2407_4_2_1_2 - [Responder Test] Not include Identification Payload
End-Node
R_RFC2407_4_2_1_2.seq [-tooloption ...] -pkt R_RFC2407_4_2_1_2.def -tooloption : v6eval tool option
See also ike_common.def and ike_ipsec.def and ike_addr.def and ike_pkt_ph1_recv.def and ike_pkt_ph2_recv.def
HOST-2(TN):initiator
|3ffe:501:ffff:101::11
|
Net-y --+--------+------------------------ 3ffe:501:ffff:101::/64
|
|
ROUTER-1(TN)
|3ffe:501:ffff:100::11
|
Net-z --+--------+------------------------ 3ffe:501:ffff:100::/64
|
|3ffe:501:ffff:100:XXXX
NUT:responder
XXXX: EUI64 address
Verification Points
All IPSEC DOI implementations MUST support SIT_IDENTITY_ONLY
by including an Identification Payload in at least one of
the Phase I Oakley exchanges and MUST abort any association setup
that does not include an Identification Payload.
Configuration
Initiator(TN) does not send ID payload by the the fifth message.
Initiator and Responder IKE parameter
At least, following parameter must be included in proposal.
| Machine |
Src |
Dest |
Phase I |
Phase II |
| Ex mode |
Key Value |
Enc Alg |
Hash Alg |
Auth Method |
DH Group |
PH1 Lt |
IDx |
Proto ID |
Trans ID |
Mode |
Auth Alg |
PH2 Lt |
Upper |
| NUT |
NUT addr |
HOST-2 addr |
Main |
IKE-TEST |
3DES |
SHA |
pre-shared key |
2 |
8 Hour |
NUT addr |
PROTO_IPSEC_ESP |
ESP_3DES |
Transport |
HMAC-SHA |
8 Hour |
any |
| HOST-2 |
HOST-2 addr |
NUT addr |
Main |
IKE-TEST |
3DES |
SHA |
pre-shared key |
2 |
8 Hour |
HOST-2 addr |
PROTO_IPSEC_ESP |
ESP_3DES |
Transport |
HMAC-SHA |
8 Hour |
any |
*Ex Mode = Exchange mode
*IDx = identity payload(FQDN or user FQDN can also be chosen as IDx)
*Enc Alg = IKE Encryption Algorithm
*Hash Alg = IKE Authentication Algorithm
*Key Value = pre-shared key value
*PH1 Lt = Phase-1 Lifetime
*PH2 Lt = Phase-2 Lifetime
*Proto ID = Protocol Identifier
*Trans ID = Transform Identifier
*Mode = Encapsulation Mode
*Auth Alg = Authentication Algorithm
*Auth Method = Authentication Method
*DH Group = Diffie-Hellman Group
*Upper = Upper Layer Protocol
*NUT addr = NUT address
*HOST-2 addr = HOST-2 address
This test check is following.
IDENTITY PROTECTION EXCHANGE
# Initiator(TN) Direction Responder(NUT)
(1) HDR; SA ========>
(2) <======== HDR; SA
(3) HDR; KE; NONCE ========>
(4) <======== HDR; KE; NONCE
(5) HDR*; HASH_I ========> <----not include ID payload(invalid)
(6) X <======== HDR*; IDir; HASH_R <----must not transmit
Judgement (Check *1)
1. Send the first message from TN
In the first message (1), the initiator generates a proposal it
considers adequate to protect traffic for the given situation. The
Security Association, Proposal, and Transform payloads are included
in the Security Association payload (for notation purposes).
2. Receive the second message from NUT
In the second message (2), the responder indicates the protection
suite it has accepted with the Security Association, Proposal, and
Transform payloads.
3. Send the third message from TN
In the third (3) message, the initiator send keying material
used to arrive at a common shared secret and random information
which is used to guarantee liveness and protect against replay attacks.
4. Receive the fourth message from NUT
In the fourth (4) message, the responder send keying material
used to arrive at a common shared secret and random information
which is used to guarantee liveness and protect against replay attacks.
5. Send the fifth message from TN
In the fifth (5) message, the initiator send identification
information and the results of the agreed upon authentication
function(hash function).
In this test, TN does not send identification information(ID payload).
6. Receive the sixth message from NUT
In the sixth (6) message, the responder send identification
information and the results of the agreed upon authentication
function(hash function).
The first to the fourth message must be exchanged correctly.
The fifth message must not be accepted. And the sixth message must not be returned.
Clean up SAD and SPD
RFC2407
4.2.1 SIT_IDENTITY_ONLY
The SIT_IDENTITY_ONLY type specifies that the security association
will be identified by source identity information present in an
associated Identification Payload. See Section 4.6.2 for a complete
description of the various Identification types. All IPSEC DOI
implementations MUST support SIT_IDENTITY_ONLY by including an
Identification Payload in at least one of the Phase I Oakley
exchanges ([IKE], Section 5) and MUST abort any association setup
that does not include an Identification Payload.
perldoc V6evalTool
IKE.html IKE Test Common Utility