SG_R_RFC2409_5_5_1 - [Responder Test] Encryption of ISAKMP payload
SGW
SG_R_RFC2409_5_5_1.seq [-tooloption ...] -pkt SG_R_RFC2409_5_5_1.def -tooloption : v6eval tool option
See also ike_common.def and ike_ipsec.def and ike_addr.def and ike_pkt_ph1_recv.def and ike_pkt_ph2_recv.def
HOST-2(TN)
|3ffe:501:ffff:104::11
|
Net-v --+------------------------+-------- 3ffe:501:ffff:104::/64
|
|
SGW-2(TN):initiator
|3ffe:501:ffff:103::11
|
Net-w --+--------+------------------------ 3ffe:501:ffff:103::/64
|
|
ROUTER-2(TN)
| 3ffe:501:ffff:102::11
|
Net-x --+--------+------------------------ 3ffe:501:ffff:102::/64
|
|3ffe:501:ffff:102::1
SGW-1(NUT):responder
|3ffe:501:ffff:101::1
|
Net-y --+--------+------------------------ 3ffe:501:ffff:101::/64
|
| 3ffe:501:ffff:101::11
ROUTER-1(TN)
|
|
Net-z -----------+---------------+-------- 3ffe:501:ffff:100::/64
|
|3ffe:501:ffff:100::13
HOST-1(TN)
Verification Points
The information exchanged along with Quick Mode MUST be protected
by the ISAKMP SA.
Configuration
Initiator and Responder IKE parameter
At least, following parameter must be included in proposal.
| Machine |
Src |
Dest |
Phase I |
Phase II |
| Ex mode |
Key Value |
Enc Alg |
Hash Alg |
Auth Method |
DH Group |
PH1 Lt |
IDx |
Proto ID |
Trans ID |
Mode |
Auth Alg |
PH2 Lt |
IDci |
IDcr |
Upper |
| SGW-1 |
SGW-1 addr |
SGW-2 addr |
Main |
IKE-TEST |
3DES |
SHA |
pre-shared key |
2 |
8 Hour |
SGW-1 addr |
PROTO_IPSEC_ESP |
ESP_3DES |
Tunnel |
HMAC-SHA |
8 Hour |
Net-v addr |
Net-z addr |
any |
| SGW-2 |
SGW-2 addr |
SGW-1 addr |
Main |
IKE-TEST |
3DES |
SHA |
pre-shared key |
2 |
8 Hour |
SGW-2 addr |
PROTO_IPSEC_ESP |
ESP_3DES |
Tunnel |
HMAC-SHA |
8 Hour |
Net-v addr |
Net-z addr |
any |
*Ex Mode = Exchange mode(Aggresive mode can also be chosen as Ex Mode)
*IDx = identity payload(FQDN or user FQDN can also be chosen as IDx)
*IDci = identity payload
*IDcr = identity payload
*Enc Alg = IKE Encryption Algorithm
*Hash Alg = IKE Authentication Algorithm
*Key Value = pre-shared key value
*PH1 Lt = Phase-1 Lifetime
*PH2 Lt = Phase-2 Lifetime
*Proto ID = Protocol Identifier
*Trans ID = Transform Identifier
*Mode = Encapsulation Mode
*Auth Alg = Authentication Algorithm
*Auth Method = Authentication Method
*DH Group = Diffie-Hellman Group
*Upper = Upper Layer Protocol
*SGW-1 addr = SGW-1 address
*SGW-2 addr = SGW-2 address
*Net-z = Net-z network address
*Net-v = Net-v network address
This test check is following.
* PHASE I
Either IDENTITY PROTECTION EXCHANGE or AGGRESSIVE EXCHANGE is performed as a pre sequence.
IDENTITY PROTECTION EXCHANGE
# Initiator(TN) Direction Responder(NUT)
(1) HDR; SA ========>
(2) <======== HDR; SA
(3) HDR; KE; NONCE ========>
(4) <======== HDR; KE; NONCE
(5) HDR*; IDii; HASH_I ========>
(6) <======== HDR*; IDir; HASH_R
1. Send the first message from TN
In the first message (1), the initiator generates a proposal it
considers adequate to protect traffic for the given situation. The
Security Association, Proposal, and Transform payloads are included
in the Security Association payload (for notation purposes).
2. Receive the second message from NUT
In the second message (2), the responder indicates the protection
suite it has accepted with the Security Association, Proposal, and
Transform payloads.
3. Send the third message from TN
In the third (3) message, the initiator send keying material
used to arrive at a common shared secret and random information
which is used to guarantee liveness and protect against replay attacks.
4. Receive the fourth message from NUT
In the fourth (4) message, the responder send keying material
used to arrive at a common shared secret and random information
which is used to guarantee liveness and protect against replay attacks.
5. Send the fifth message from TN
In the fifth (5) message, the initiator send identification
information and the results of the agreed upon authentication
function(hash function).
6. Receive the sixth message from NUT
In the sixth (6) message, the responder send identification
information and the results of the agreed upon authentication
function(hash function).
AGGRESSIVE EXCHANGE
# Initiator(TN) Direction Responder(NUT) NOTE
(1) HDR; SA; KE; => Begin ISAKMP-SA or
Proxy negotiation
NONCE; IDii and Key Exchange
(2) <= HDR; SA; KE;
NONCE; IDir; AUTH
Initiator Identity
Verified by Responder
Key Generated
Basic SA agreed upon
(3) HDR*; AUTH =>
Responder Identity
Verified by Initiator
SA established
1. Send the first message from TN
In the first message (1), the initiator generates a proposal it
considers adequate to protect traffic for the given situation. The
Security Association, Proposal, and Transform payloads are included
in the Security Association payload (for notation purposes). There
can be only one Proposal and one Transform offered (i.e. no choices)
in order for the aggressive exchange to work. Keying material used
to arrive at a common shared secret and random information which is
used to guarantee liveness and protect against replay attacks are
also transmitted. Random information provided by both parties SHOULD
be used by the authentication mechanism to provide shared proof of
participation in the exchange. Additionally, the initiator transmits
identification information.
2. Recieve the second message from NUT
In the second message (2), the responder indicates the protection
suite it has accepted with the Security Association, Proposal, and
Transform payloads. Keying material used to arrive at a common
shared secret and random information which is used to guarantee
liveness and protect against replay attacks is also transmitted.
Random information provided by both parties SHOULD be used by the
authentication mechanism to provide shared proof of participation in
the exchange. Additionally, the responder transmits identification
information. All of this information is transmitted under the
protection of the agreed upon authentication function. Local
security policy dictates the action of the responder if no proposed
protection suite is accepted. One possible action is the
transmission of a Notify payload as part of an Informational
Exchange.
3. Send the third message from TN
In the third (3) message, the initiator transmits the results of the
agreed upon authentication function. This information is transmitted
under the protection of the common shared secret. Local security
policy dictates the action if an error occurs during these messages.
One possible action is the transmission of a Notify payload as part
of an Informational Exchange.
The test sequence is following.
* PHASE II
QUICK MODE
# Initiator(TN) Direction Responder(NUT)
(1) HDR*, HASH(1),
SA, Ni,IDci, IDcr; ========>
(2) <======== HDR*, HASH(2), SA, Nr, IDci, IDcr;
Judgement (Check *1)
1. Send the first message from TN
In the first message (1), the initiator generates a proposal it
considers adequate to protect traffic for the given situation. The
Security Association, Proposal, and Transform payloads are included
in the Security Association payload (for notation purposes).
And initiator send HASH(1) and Nonce. HASH(1) is the prf over the
message id (M-ID) from the ISAKMP header concatenated with the entire
message that follows the hash including all payload headers,
but excluding any padding added for encryption. Nonce is random
information which is used to guarantee liveness. IDci and IDcr is
identification information.
2. Receive the second message from NUT
In the second message (2), the responder indicates the protection
suite it has accepted with the Security Association, Proposal, and
Transform payloads. And responder send HASH(2) and Nonce.
HASH(2) is identical to HASH(1) except the initiator's nonce-- Ni,
minus the payload header-- is added after M-ID but before the
complete message. Nonce is random
information which is used to guarantee liveness. IDci and IDcr is
identification information.
In Phase I , messages must be exchanged correctly.
In Phase II , the first message must be accepted. And the second message must be
encrypted and returned.
And must conform to above Configuration.
Clean up SAD and SPD
RFC2408
3.1 ISAKMP Header Format
(omit)
o Flags (1 octet) - indicates specific options that are set for the
ISAKMP exchange. The flags listed below are specified in the
Flags field beginning with the least significant bit, i.e the
Encryption bit is bit 0 of the Flags field, the Commit bit is bit
1 of the Flags field, and the Authentication Only bit is bit 2 of
the Flags field. The remaining bits of the Flags field MUST be
set to 0 prior to transmission.
-- E(ncryption Bit) (1 bit) - If set (1), all payloads following
the header are encrypted using the encryption algorithm
identified in the ISAKMP SA. The ISAKMP SA Identifier is the
combination of the initiator and responder cookie. It is
RECOMMENDED that encryption of communications be done as soon
as possible between the peers. For all ISAKMP exchanges
described in section 4.1, the encryption SHOULD begin after
both parties have exchanged Key Exchange payloads. If the
E(ncryption Bit) is not set (0), the payloads are not
encrypted.
(omit)
RFC2409
3.2 Notation
(omit)
Message encryption (when noted by a '*' after the ISAKMP header) MUST
begin immediately after the ISAKMP header. When communication is
protected, all payloads following the ISAKMP header MUST be
encrypted. Encryption keys are generated from SKEYID_e in a manner
that is defined for each algorithm.
(omit)
5.5 Phase 2 - Quick Mode
Quick Mode is not a complete exchange itself (in that it is bound to
a phase 1 exchange), but is used as part of the SA negotiation
process (phase 2) to derive keying material and negotiate shared
policy for non-ISAKMP SAs. The information exchanged along with Quick
Mode MUST be protected by the ISAKMP SA-- i.e. all payloads except
the ISAKMP header are encrypted. In Quick Mode, a HASH payload MUST
immediately follow the ISAKMP header and a SA payload MUST
immediately follow the HASH. This HASH authenticates the message and
also provides liveliness proofs.
(omit)
perldoc V6evalTool
IKE.html IKE Test Common Utility