CHANGELOG for IPv6 Ready Logo Phase-1/Phase-2 Core Protocols Conformance Test Package 2008/05/09 Release 1.4.15 Official release 2008/05/09 Yukiyo Akisada M addr.p2/RA_SAA.def - Allow to use the unspecified address as Source Address field in RS 2008/05/08 Yukiyo Akisada M nd.p2/redirect.def, v6LC_2_3_17.def - Change not to use Link1 at host test cases 2008/05/07 Yukiyo Akisada M nd.p2/v6LC_2_3_3_G.{def,seq} - Correct checksum 2008/04/24 Release 1.4.14 Official release 2008/03/26 Yukiyo Akisada M nd.p2/common.def, redirect.{def,pm}, v6LC_2_3_17.seq - v6LC.2.3.17: Updated procedure step 4 and 5 to use Rut's routing table 2008/03/05 Release 1.4.13 Official release 2008/03/05 Yukiyo Akisada M nd.p2/V6LC_2_1_7.seq, v6LC_2_1_6_[B-D]-v3_8_2.seq (v6LC.2.1.6) - correct Common Setup 1.1 M nd.p2/ndisc.pm - change to remove default route after flush neighbor cache 2008/03/04 Release 1.4.12 Official release 2008/03/04 Yukiyo Akisada M nd.p2/V6LC_2_1_1_D.seq, V6LC_2_1_7.seq, v6LC_2_1_13_[A-C]-v3_8_2.seq, v6LC_2_1_6_[B-D]-v3_8_2.seq - correct the use of boolean value 2008/02/20 Release 1.4.11 Official release 2008/02/20 Yukiyo Akisada M nd.p2/v6LC_2_2_7_B.def - correct Router Lifetime value of expected packet definition 2008/02/15 Release 1.4.10 Official release 2008/02/06 Yukiyo Akisada M nd.p2/V6LC_2_1_1_[A-D].seq V6LC_2_1_2_[A-B].seq V6LC_2_1_3.{seq,def} V6LC_2_1_5_[A-B].{seq,def} V6LC_2_1_6_[A-B].{seq,def} V6LC_2_1_6_A_p1.seq v6LC_2_1_6_[B-D]-v3_8_2.{seq,def} V6LC_2_1_7.{seq,def} V6LC_2_1_8_[A-H].seq v6LC_2_1_8_C-v3_8_2.seq V6LC_2_1_9_[A-B].seq v6LC_2_1_9_C-v3_8_2.{seq,def} V6LC_2_1_10_[A-B].seq V6LC_2_1_11_[A-D].seq V6LC_2_1_12_[A-D].seq V6LC_2_1_13_[A-D].seq v6LC_2_1_13_[A-C]-v3_8_2.{seq,def} V6LC_2_1_14.seq V6LC_2_1_15_[A-G].seq V6LC_2_1_16_[A-H].seq V6LC_2_1_17_[A-E].seq V6LC_2_1_18_[A-R].seq V6LC_2_1_19_[A-R].seq V6LC_2_1_20_[A-R].seq V6LC_2_1_21_[A-H].{seq,def} nd.pm ndisc.pm ndisc_common.def ndisc_echo.def ndisc_na.def ndisc_ns.def ndisc_ra.def - correct cleanup procedure 2008/02/01 Yukiyo Akisada M pmtu.p2/receiveMTU0.seq M pmtu.p2/receiveMTU512.seq - typo in perldoc M index.html.TAKE - change title from Phase-2 to Phase-1/Phase-2 M addr.p2/Makefile.test M nd.p2/Makefile.test - change to re-generate AdvancedFunctionality.{pm,def} M icmp.p2/Err_Condition_Port_UnspecAddr.def (v6LC.5.1.11.A) M icmp.p2/Err_Condition_Port_GMaddr.def (v6LC.5.1.12.A) - handle neighbor discovery for invalid packet M nd.p2/V6LC_2_1_1_B.seq - wait for NUT to be NONCE befor exit 2007/10/01 Release 1.4.9 Official release 2007/09/26 Yukiyo Akisada nd.p2/v6LC_2_3_6_G.def - correct packet definition 2007/06/21 Release 1.4.8 Official release 2007/06/21 Yukiyo.Akisada@jp.yokogawa.com nd.p2/V6LC_2_2_12_A.{def,seq}, V6LC_2_2_12_B.{def,seq}, rdisc.pm - fix the verification of CurHopLimit in Test v6LC.2.2.13 2007/04/13 Release 1.4.7 Official release 2007/04/11 Yukiyo.Akisada@jp.yokogawa.com spec.p2/EX_NH_UnrecognizedEN.seq, IP_NH_Unrecognized.seq - fix the conflict of unrecognized Next Header values 2007/01/30 Yukiyo.Akisada@jp.yokogawa.com spec.p2/{HHO_MSB10mc_EN,HHO_MSB11mc_EN}.seq - Change to Basic Functionality Tests. * These test are not Advanced Functionality Tests. 2006/12/14 Hideshi.Enokihara@jp.yokogawa.com pmtu.p2/mcastOne.seq - fix the lack of unexpected packet processing pmtu.p2/mcastTwo.seq - fix the lack of unexpected packet processing 2006/12/13 Yukiyo.Akisada@jp.yokogawa.com nd.p2/nd.pm - Editorial Bug Fix: correct %pktdesc() for V6LC_2_1_2_B.seq 2006/12/06 Hideshi.Enokihara@jp.yokogawa.com pmtu.p2/increase1500.seq - fix the lack of unexpected packet processing pmtu.p2/increase0x1fffffff.seq - fix the lack of unexpected packet processing 2006/12/04 Release 1.4.6 Official release 2006/12/04 Yukiyo.Akisada@jp.yokogawa.com nd.p2/INDEX_ND_p1_{host,special} - use V6LC_2_1_6_A_p1.seq for v6LC.2.1.5(A) as like as INDEX_ND_p1_router 2006/11/29 Release 1.4.5 Official release 2006/11/29 Yukiyo.Akisada@jp.yokogawa.com nd.p2/v6LC_2_2_7_C_p1.def - fix the lack of packet definition file 2006/11/28 Release 1.4.4 Official release 2006/11/28 Yukiyo.Akisada@jp.yokogawa.com nd.p2/INDEX_ND_p1_router, V6LC_2_1_6_A_p1.seq - remove AdvRetransTimer=5000 milliseconds test cases from Phase-1 router test sets This modification will allow the NUT to behave loose in v6LC.2.1.5(A) only for Phase-1 router test case nd.p2/ndisc.pm - allow to use link-local address as the source address of multicast NS This modification will allow the NUT to behave loose in v6LC.2.1.6(C) for Phase-1/Phase-2 IPv6 Core Protocols nd.p2/INDEX_RD_p1_router, rdisc.pm, v6LC_2_2_7_C_p1.seq - remove to test omission of MTU option This modification will allow the NUT to behave loose in v6LC.2.2.7(C) only for Phase-1 router test case pmtu.p2/mcastOne.seq, mcastTwo.seq - avoid to fall in internal error when NUT doesn't send any packet 2006/09/26 Release 1.4.3 Official release 2006/09/26 Yukiyo.Akisada@jp.yokogawa.com spec.p2/CommonSPEC.pm - send RA when NUT is the special device CommonSPEC::setup11_v6LC_1_3_2() CommonSPEC::cleanup_v6LC_1_3_2() CommonSPEC::cleanup_v6LC_1_3_2_D() This modification will correct the behavior of v6LC.1.3.2(A-E). 2006/08/04 Release 1.4.2 Official release 2006/08/04 Yukiyo.Akisada@jp.yokogawa.com nd.p2/{common,rdisc}.pm - add cleanup procedure with $rut_rtadvd_param_change 2006/07/27 Release 1.4.1 Official release 2006/07/26 Yukiyo.Akisada@jp.yokogawa.com icmp.p2/Echo_Global.seq, icmp.pm - support 'special' as NutDef{'Type'} for Phase-1 test in Common Test Setup 2006/07/25 Yukiyo.Akisada@jp.yokogawa.com nd.p2/common.pm - support 'special' as NutDef{'Type'} for Phase-1 test in Common Test Cleanup 2006/06/07 Release 1.4.0 Official release 2005/06/02 Yukiyo.Akisada@jp.yokogawa.com nd.p2/V6LC_2_2_13_[B-C].{def,seq}, rdisc.pm - changed to retain 2 entries in default router list instead of 3. v6LC.2.2.14 (B), v6LC.2.2.14 (C) 2005/05/25 Yukiyo.Akisada@jp.yokogawa.com nd.p2/nd.pm - change to call vSend() for each packets V6LC.2.1.2 (A), V6LC.2.1.2 (B) 2006/04/28 Release 1.4.0b1 Official release 2005/04/28 Yukiyo.Akisada@jp.yokogawa.com nd.p2/rdisc.pm v6LC_2_2_7_[B-D].{def,seq}. v6LC_2_2_10_[A-I].{def,seq}. v6LC_2_2_17_[A-C].{def,seq}. v6LC_2_2_18.{def,seq}. addr.p2/v6LC_3_2_1.seq - add new tests 2005/04/27 Yukiyo.Akisada@jp.yokogawa.com nd.p2/common.pm, rdisc.pm v6LC_2_2_16_{E,[H-K]}-v3_8_2.{def,seq} - add new tests 2005/04/26 Yukiyo.Akisada@jp.yokogawa.com spec.p2/CommonSPEC.pm, v6LC_1_1_5_B.{def,seq}, v6LC_1_3_2_D.{def,seq} nd.p2/nd.pm, ndisc.pm, v6LC_2_1_6_[B-D]-v3_8_2.{def,seq}, v6LC_2_1_8_C-v3_8_2.{def,seq}, v6LC_2_1_9_C-v3_8_2.{def,seq}, v6LC_2_1_13_[A-C]-v3_8_2.{def,seq}, v6LC_2_1_18_[Q-R].{def,seq}, v6LC_2_1_19_[Q-R].{def,seq}, V6LC_2_1_20_[Q-R].{def,seq}, V6LC_2_1_21_[E-H].{def,seq} - add new tests 2006/04/17 Release 1.3.7 Official release 2005/03/13 Yukiyo.Akisada@jp.yokogawa.com icmp.p2/INDEX_P2_host - remove Test v6LC.5.1.13 from host tests 2005/03/09 Yukiyo.Akisada@jp.yokogawa.com icmp.p2/Pkt_Too_Big.{def,seq}, icmp.{def,pm} (Test v6LC.5.1.4 (A)) - make sure to create neighbor cache entry for TN1 and TN2 2006/03/07 Release 1.3.6 Official release 2005/03/06 Hideshi.Enokihara@jp.yokogawa.com nd.p2/V6LC_2_2_9_B.seq, rdisc.pm (Test v6LC.2.2.9 (B)) - correct the name of packet definition to use 2005/03/03 Yukiyo.Akisada@jp.yokogawa.com nd.p2/rdisc.{def,pm} (Test v6LC.2.2.8) - Allow NUT to remove Prefix Information option from RA, when NUT stops sending RA. 2006/02/02 Release 1.3.5 Official release 2005/02/01 Yukiyo.Akisada@jp.yokogawa.com icmp.p2/Pkt_Too_Big.def (Test v6LC.5.1.4 (A)) - Correct MTU value in Packet Too Big used at when HAS_MULTIPLE_INTERFACES is false 2006/01/20 Release 1.3.4 Official release 2005/01/20 Yukiyo.Akisada@jp.yokogawa.com nd.p2/V6LC_2_1_6_A.seq V6LC_2_1_6_B.seq V6LC_2_1_7.seq - wait DAD after RA 2006/01/19 Release 1.3.3 Official release 2005/01/18 Yukiyo.Akisada@jp.yokogawa.com pmtu.p2/CommonPMTU.pm - reboot at every cleanup - Support test specification ver.3.7.1 pmtu.p2/CommonHost.def - set prefix lifetime as long enough such that they do not expire during the test 2006/01/13 Release 1.3.2 Official release 2005/01/12 Yukiyo.Akisada@jp.yokogawa.com icmp.p2/To_Multi_Pkt_Too_Big.seq - correct to call function which set MTU (Test v6LC.5.1.4 (A)) nd.p2/{common, rdisc}.pm - add cleanup procedure (Test v6LC.2.2.12 (B)) - add cleanup procedure (Test v6LC.2.2.14) 2005/01/11 Yukiyo.Akisada@jp.yokogawa.com Makefile.inc - define V6EVALROOT variable nd.p2/ndisc.pm - fix typo nd.p2/rdisc.pm - correct variable name 2006/01/10 Release 1.3.1 Official release 2005/01/10 Yukiyo.Akisada@jp.yokogawa.com nd.p2/V6LC_2_1_6_A.seq, V6LC_2_1_6_B.seq, ndisc.pm - correct cleanup procedure (Test v6LC.2.1.5) icmp.p2/Err_Condition_Port_Unreachable.seq, Err_Condition_Port_ACaddr.def (Test v6LC.5.1.13 (A)) - handle neighbor discovery for invalid packet 2006/01/06 Release 1.3 Official release 2005/12/01 Release 1.3.0b1 Official release 2005/12/01 Yukiyo.Akisada@jp.yokogawa.com - support the router which has only one physical interface 2005/11/30 Yukiyo.Akisada@jp.yokogawa.com spec.p2/EX_NH_UnrecognizedEN.def - add payload to Packet A (Test v6LC.1.2.3 Part A) nd.p2/rdisc.{pm,def}, common_ra.def - allow RUT to send RA with MTU option (Test v6LC.2.2.5) nd.p2/rdisc.{pm,def}, common_ra.def - allow RUT to send RA with MTU option (Test v6LC.2.2.6 Part B) nd.p2/rdisc.{pm,def}, common_ra.def, V6LC_2_2_7.{seq,def} - allow RUT to send RA with MTU option (Test v6LC.2.2.7) nd.p2/rdisc.{pm,def}, common_ra.def - allow RUT to send RA with MTU option (Test v6LC.2.2.8) nd.p2/rdisc.{pm,def}, common_ra.def - allow RUT to send RA with MTU option (Test v6LC.2.2.9 Part A) nd.p2/rdisc.{pm,def}, common_ra.def, V6LC_2_2_9_B.def - allow RUT to send RA with MTU option (Test v6LC.2.2.9 Part B) pmtu.p2/INDEX_p2_router, receiveMTU0.{seq,def} - change MTU in Packet Too Big from 0 to 56 (Test v6LC.4.1.6 Part A) pmtu.p2/INDEX_p2_router, receiveMTU512.{seq,def} - change MTU in Packet Too Big from 512 to 1279 (Test v6LC.4.1.6 Part B) 2005/07/20 Release 1.2.18 Official release 2005/07/20 Yukiyo.Akisada@jp.yokogawa.com nd.p2/INDEX_RD_p2_router, V6LC_2_2_8_B.{seq,def} - remove Test v6LC.2.2.8 Part B 2005/07/19 Release 1.2.17 Official release 2005/07/19 Yukiyo.Akisada@jp.yokogawa.com spec.p2/IP_NH_Unrecognized.def - correct Payload Length in IPv6 Header (Test v6LC.1.1.7 Part A) spec.p2/HHO_MSB10mc_IN.def - correct L2 destination address of multicast packet (Test v6LC.1.2.7 Part G) nd.p2/V6LC_2_1_6_A.seq, V6LC_2_1_6_B.{seq,def} ndisc.pm, ndisc_common.def - satisfy test specification (Test v6LC.2.1.5) icmp.p2/To_Multi_Pkt_Too_Big.def - correct L2 destination address of multicast packet (Test v6LC.5.1.4 Part B) 2005/07/05 Yukiyo.Akisada@jp.yokogawa.com nd.p2/v6LC_2_3_6_B.seq (Test v6LC.2.3.6 Part B) - fix typo in perldoc 2005/06/20 Release 1.2.16 Official release 2005/06/14 Yukiyo.Akisada@jp.yokogawa.com Support IPv6 READY Phase II Test Specification Revision 3.6.0 nd.p2/INDEX_ND_p2_host, ndisc.{pm,def}, V6LC_2_1_4.{seq,def} - remove Test v6LC.2.1.4 2005/06/02 Yukiyo.Akisada@jp.yokogawa.com pmtu.p2/storedPMTU.seq, CommonPMTU.pm, CommonHost.def (Test v6LC.4.1.2) - increase AdvDefaultLifetime not to expire during the test pmtu.p2/CommonHost.def (Common Test Cleanup) - correct AdvReachableTime and AdvRetransTimer for sending RA - remove SLL option for sending RA for sending RA - add MTU option for sending RA for sending RA 2005/05/31 Release 1.2.15 Official release 2005/05/31 Yukiyo.Akisada@jp.yokogawa.com icmp.p2/To_ICMPErr_Packet_Too_Big.def (Test v6LC.5.1.9 Part E) - correct MAC address of packet to send 2005/05/25 Release 1.2.14 Official release 2005/05/12 Yukiyo.Akisada@jp.yokogawa.com spec.p2/R_Processing_HELodd_IN.def (Test v6LC.1.2.15 Part A) - allow to use Link1 address for Parameter Problem nd.p2/V6LC_2_1_7.seq (Test v6LC.2.1.7) - change to ignore unexpected packets which aren't related to test addr.p2/SAA.pm - change to call vClrear() before vSend() and remove seektime for vRect(). pmtu.p2/storedPMTU.{seq,def} - make it sure to keep neighbor cache for TN1&TR1 (v6LC.4.1.2) pmtu.p2/reducePMTUonlink.seq, CommonPMTU.pm - create neighbor cache for TR1 global address at setup 2005/04/27 Release 1.2.13 Official release 2005/04/27 Yukiyo.Akisada@jp.yokogawa.com pmtu.p2/reducePMTUonlink.{seq,def} (Test v6LC.4.1.4) - add sequence to test also for global scope - correct echo request packet size as like as test specification 2005/04/25 Yukiyo.Akisada@jp.yokogawa.com icmp.p2, nd.p2, pmtu.p2, spec.p2 - enable to configure delay time for reboot by config.pl 2005/04/14 Release 1.2.12 Official release 2005/04/14 Yukiyo.Akisada@jp.yokogawa.com nd.p2/V6LC_2_1_21_[A-D].seq, ndisc.def, ndisc.pm - correct common cleanup procedure nd.p2/V6LC_2_2_3_[A-C].seq, rdisc.pm, common.pm - insert 3 seconds delay after transmitting RS nd.p2/v6LC_2_3_10_[A-D].seq, redirect.pm - insert 3 seconds delay after transmitting Redirect nd.p2/v6LC_2_3_12_[A-E].seq, redirect.pm - insert 3 seconds delay after transmitting Redirect nd.p2/v6LC_2_3_13_[A-E].seq, redirect.pm - insert 3 seconds delay after transmitting Redirect nd.p2/v6LC_2_3_14_[C-E].seq, redirect.pm - insert 3 seconds delay after transmitting Redirect nd.p2/v6LC_2_3_15_[A-I].seq, redirect.pm - insert 3 seconds delay after transmitting Redirect 2005/04/13 Yukiyo.Akisada@jp.yokogawa.com nd.p2/V6LC_2_1_8_A.{seq,def} - use all-nodes multicast address instead of solicited-node multicast address as the invalid NS's target address nd.p2/V6LC_2_2_10.{seq,def} - use 1,000 milliseconds as AdvRetransTimer nd.p2/V6LC_2_2_11_[A-F].{seq,def} - use 20 seconds as AdvDefaultLifetime - use 600,000 milliseconds as AdvReachableTime - use 1,000 milliseconds as AdvRetransTimer nd.p2/V6LC_2_2_13_[A-C].{seq,def}, common_ra.def, rdisc.pm, common.pm - use 600,000 milliseconds as AdvReachableTime - use 1,000 milliseconds as AdvRetransTimer - use 100 seconds as AdvValidLifetime - use 20 seconds as AdvPreferredLifetime nd.p2/V6LC_2_2_15_[A-F].{seq,def} - use 10,000 milliseconds as AdvReachableTime - use 1,000 milliseconds as AdvRetransTimer 2005/03/11 Release 1.2.11 Official release 2005/03/10 Hiroki.Endou@jp.yokogawa.com spec.p2/CommonHost.def spec.p2/CommonSPEC.pm spec.p2/F_TX_intime.seq, spec.p2/F_TX_expire.seq spec.p2/F_TX_only1st.seq spec.p2/F_TX_only2nd.seq - change to perform Common Test Setup 1.1 in v6LC.1.3.2 2005/03/09 Release 1.2.10 Official release 2005/03/08 Hiroki.Endou@jp.yokogawa.com icmp.p2/Pkt_Too_Big.seq icmp.p2/Pkt_Too_Big.def icmp.p2/To_Multi_Pkt_Too_Big.seq icmp.p2/Err_Condition_Too_Big.seq icmp.p2/Err_Condition_Too_Big_ACaddr.def icmp.p2/Err_Condition_Too_Big_GMaddr.def icmp.p2/Err_Condition_Too_Big_UnspecAddr.def - remove unnecessary sequence to add route and make NCE modify TN2 address 2005/03/07 Hiroki.Endou@jp.yokogawa.com icmp.p2/To_Multi_Pkt_Too_Big.seq - remove unnecessary sequence in v6LC.5.1.4.B spec.p2/IP_TC_NonZeroEN.seq, IP_TC_NonZeroEN.def spec.p2/IP_TC_NonZeroIN.seq, IP_TC_NonZeroIN.def - change to use 0x20 as Traffic Class value in v6LC.1.1.2 and v6LC.1.1.3 spec.p2/R_Processing_HELodd_IN.seq - correct interface transmitting Packet A in v6LC.1.2.15 spec.p2/F_TX_intime.seq, F_TX_intime.def spec.p2/F_TX_expire.seq, F_TX_expire.def spec.p2/F_TX_only1st.seq, F_TX_only1st.def spec.p2/F_TX_only2nd.seq, F_TX_only2nd.def - change to use global address in v6LC.1.3.2 2005/03/04 Hiroki.Endou@jp.yokogawa.com icmp.p2/Dst_Unreach_3_Global.seq, Dst_Unreach_3_Global.def - change packet definition into on-link global address in v6LC.5.1.3.B icmp.p2/To_Multi_Pkt_Too_Big.seq, To_Multi_Pkt_Too_Big.def - correct global multicast address in v6LC.5.1.4.B icmp.p2/P_Problem_Err_Header_Field.seq icmp.p2/P_Problem_Err_Header_Field.def - correct ICMPv6 Data Length in Packt A in v6LC.5.1.6 icmp.p2/P_Problem_Global.seq, icmp.p2/P_Problem_Global.def - append ICMPv6 header to Packt A in v6LC.5.1.7 2005/02/22 Release 1.2.9 Official release 2005/02/22 Yukiyo.Akisada@jp.yokogawa.com spec.p2/HHO_MSB10mc_IN.seq, HHO_MSB11mc_IN.seq HHO_MSB10mc_IN.def, HHO_MSB11mc_IN.def - add procedure for multicast routing in v6LC.1.2.7.G,H nd.p2/rdisc.pm - correct expiration timer in v6LC.2.2.13.A 2005/02/18 Yukiyo.Akisada@jp.yokogawa.com addr.p2/v6LC_3_2_4_C.seq (was addr.p2/RA_decVLT.seq) - correct test sequence to fit test specification 2005/02/17 Yukiyo.Akisada@jp.yokogawa.com spec.p2/EX_NH_UnrecognizedEN.seq spec.p2/EX_NH_UnrecognizedEN.def - remove difference between perldoc and packet definition in v6LC.1.2.3.A nd.p2/common.pm, common_echo.def common_tn_na.def, common_tn_ns.def redirect.pm, v6LC_2_3_16_A.seq - add ND handling for on-link destination in v6LC.2.3.16.A 2005/02/01 Yukiyo.Akisada@jp.yokogawa.com nd.p2/ndisc.pm nd.p2/rdisc.pm correct vRecv() arguments 2005/01/21 Release 1.2.8 Official release 2005/01/21 Hiroki.Endou@jp.yokogawa.com spec.p2/HHO_MSB10mc_IN.def spec.p2/HHO_MSB11mc_IN.def - correct packet definition nd.p2/rdisc.pm - correct pass condition 2005/01/20 Release 1.2.7 Official release 2005/01/20 Hiroki.Endou@jp.yokogawa.com spec.p2/R_Processing_HELodd_IN.seq spec.p2/R_Processing_SegLftGTadr_IN.seq spec.p2/R_Processing_AdrMC_IN.seq spec.p2/R_Processing_DstMC_IN.seq spec.p2/R_Processing_HL0_IN.seq spec.p2/R_Processing_HL1_IN.seq spec.p2/R_Processing_Valid_IN.seq spec.p2/R_UnrecognizedRoutingTypeEN.seq spec.p2/R_UnrecognizedRoutingTypeIN.seq - correct perldoc spec.p2/CommonHost.def - change ReachableTime value spec.p2/CommonSPEC.pm spec.p2/F_Reassembly_1500.seq - change to process lightly pmtu.p2/CommonPMTU.pm - change to process lightly 2005/01/19 Hiroki.Endou@jp.yokogawa.com spec.p2/CommonSPEC.pm - remove needless default route setup in Common Setup 1.2 for v6LC.1.2.11 spec.p2/R_Processing_HELodd_IN.def - correct packet definition of Routing Header nd.p2/redirect.pm nd.p2/v6LC_2_3_1_A.seq nd.p2/v6LC_2_3_1_B.seq nd.p2/v6LC_2_3_1_E.seq nd.p2/v6LC_2_3_1_F.seq - cancel previous changes of v6LC.2.3.1.A, B, E and F 2005/01/18 Release 1.2.6 Official release 2005/01/17 Hiroki.Endou@jp.yokogawa.com nd.p2/nd.pm nd.p2/V6LC_2_1_21_A.seq nd.p2/V6LC_2_1_21_B.seq nd.p2/V6LC_2_1_21_C.seq nd.p2/V6LC_2_1_21_D.seq nd.p2/rdisc.pm nd.p2/V6LC_2_2_13_A.seq nd.p2/V6LC_2_2_13_B.seq nd.p2/V6LC_2_2_13_C.seq nd.p2/redirect.pm nd.p2/v6LC_2_3_1_A.seq nd.p2/v6LC_2_3_1_B.seq nd.p2/v6LC_2_3_1_E.seq nd.p2/v6LC_2_3_1_F.seq - correct test sequnce for not using onlink assumption spec.p2/EX_NH_NoneIN.def - correct Checksum value spec.p2/EX_NH_NoneIN.def - correct Extention Header spec.p2/CommonSPEC.pm spec.p2/F_Reassembly_1500.seq spec.p2/F_Reassembly_1500.def - adapt fragmentation 2005/01/14 Release 1.2.5 Official release 2005/01/14 Yukiyo.Akisada@jp.yokogawa.com nd.p2/redirect.pm - correct procedure related to v6LC.2.3.14 to change reachablity state to PROBE 2005/01/14 Yukiyo.Akisada@jp.yokogawa.com nd.p2/v6LC_2_3_10_D.seq nd.p2/v6LC_2_3_11_A.seq nd.p2/v6LC_2_3_11_D.seq nd.p2/v6LC_2_3_12_E.seq nd.p2/v6LC_2_3_13_A.seq nd.p2/v6LC_2_3_13_B.seq nd.p2/v6LC_2_3_13_E.seq nd.p2/v6LC_2_3_14_A.seq nd.p2/v6LC_2_3_14_B.seq nd.p2/v6LC_2_3_14_E.seq - correct packet description 2005/01/14 Yukiyo.Akisada@jp.yokogawa.com nd.p2/V6LC_2_1_20_A.seq nd.p2/V6LC_2_1_20_B.seq nd.p2/V6LC_2_1_20_C.seq nd.p2/V6LC_2_1_20_D.seq nd.p2/V6LC_2_1_20_E.seq nd.p2/V6LC_2_1_20_F.seq nd.p2/V6LC_2_1_20_G.seq nd.p2/V6LC_2_1_20_H.seq nd.p2/V6LC_2_1_20_I.seq nd.p2/V6LC_2_1_20_J.seq nd.p2/V6LC_2_1_20_K.seq nd.p2/V6LC_2_1_20_L.seq nd.p2/V6LC_2_1_20_M.seq nd.p2/V6LC_2_1_20_N.seq nd.p2/V6LC_2_1_20_O.seq nd.p2/V6LC_2_1_20_P.seq - correct procedure to change reachablity state to PROBE 2005/01/14 Hiroki.Endou@jp.yokogawa.com nd.p2/V6LC_2_1_13_A.seq nd.p2/V6LC_2_1_13_B.seq nd.p2/V6LC_2_1_13_C.seq nd.p2/V6LC_2_1_13_D.seq nd.p2/ndisc.pm - correct procedure to change reachablity state to PROBE 2005/01/14 Release 1.2.4 Official release 2005/01/14 Yukiyo.Akisada@jp.yokogawa.com nd.p2/ndisc.def nd.p2/ndisc.pm - correct clean up procedure related to V6LC_2_1_5_A 2005/01/14 Hiroki.Endou@jp.yokogawa.com nd.p2/V6LC_2_1_6_A.seq nd.p2/V6LC_2_1_6_B.seq - modify packet waiting time pmtu.p2/storedPMTU.seq - insert vClear before each transmitting Echo Request pmtu.p2/mcastOne.seq pmtu.p2/mcastTwo.seq - insert vClear before each ping6.rmt spec.p2/Makefile.test pmtu.p2/Makefile.test icmp.p2/Makefile.test - modify AdvancedFunctionality.pm creation rule 2005/01/13 Release 1.2.3 Official release 2005/01/13 Hiroki.Endou@jp.yokogawa.com spec.p2/INDEX_p2_host spec.p2/INDEX_p2_router - remove a test v6LC.1.2.14.C spec.p2/R_Processing_HELodd_IN.def - correct packet definition spec.p2/IP_NH_NoneIN.def - correct packet definition nd.p2/V6LC_2_1_13_A.def nd.p2/V6LC_2_1_13_B.def nd.p2/V6LC_2_1_13_C.def nd.p2/V6LC_2_1_13_D.def - add packet definition include file nd.p2/nd.p2 - correct NS retransmit timer margin calculation for V6LC.2.1.7 icmp.p2/To_ICMPErr_Dst_Unreach_0.def - correct Hdr_Ether of Prameter Problem message icmp.p2/INDEX_P2_router icmp.p2/To_ICMPErr_Dst_Unreach_0.def icmp.p2/To_ICMPErr_Dst_Unreach_0.seq icmp.p2/To_ICMPErr_Dst_Unreach_3.def icmp.p2/To_ICMPErr_Dst_Unreach_3.seq icmp.p2/To_ICMPErr_Packet_Too_Big.def icmp.p2/To_ICMPErr_Packet_Too_Big.seq icmp.p2/To_ICMPErr_Parameter_Problem.def icmp.p2/To_ICMPErr_Parameter_Problem.seq icmp.p2/To_ICMPErr_Time_Exc_Code0.def icmp.p2/To_ICMPErr_Time_Exc_Code0.seq icmp.p2/To_ICMPErr_Time_Exc_Code1.def icmp.p2/To_ICMPErr_Time_Exc_Code1.seq - correct test sequence 2005/01/12 Release 1.2.2 Official release 2005/01/12 Hiroki.Endou@jp.yokogawa.com nd.p2/V6LC_2_1_1_B.seq - modify for removing on-link assumption nd.p2/INDEX_RD_p2_host - correct test title nd.p2/V6LC_2_1_20_A.seq - V6LC_2_1_20_P.seq nd.p2/ndisc.pm - modify procedure for state transition to PROBE icmp.p2/Pkt_Too_Big.seq icmp.p2/To_Multi_Pkt_Too_Big.def - correct interface which Package Too Big Message is transmitted spec.p2/R_Processing_HELodd_IN.seq - add common setup 1.1 pmtu.p2/INDEX_p2_host - delete an obsolete test 2005/01/12 Yukiyo.Akisada@jp.yokogawa.com nd.p2/ndisc.def nd.p2/ndisc.pm - correct clean up procedure related to V6LC_2_1_5_A 2005/01/12 Yukiyo.Akisada@jp.yokogawa.com nd.p2/V6LC_2_2_11_A.seq nd.p2/V6LC_2_2_11_A.def - correct source address of test packet 2005/01/06 Hiroki.Endou@jp.yokogawa.com spec.p2/IP_NH_Unexpected.seq spec.p2/IP_NH_Unexpected.def - modify Identification value in transmitting Fragment Header - modify Pointer value in expected ICMP Error message 2004/12/29 Release 1.2.1 Official release 2004/12/29 Hiroki.Endou@jp.yokogawa.com icmp.p2/Time_Exc.def - modify to receive multiple source address addr.p2/RA_gt2lt2.seq - modify to time correctly nd.p2/ndisc.pm - modify to transmit global address cleanup NS for v6LC.2.1.4 nd.p2/v6LC_2_0_0.seq - modify to wait RSs after initialization 2004/11/29 Release 1.2 Official release 2004/11/29 Hiroki.Endou@jp.yokogawa.com nd.p2/V6LC_2_2_12_A.seq nd.p2/V6LC_2_1_12_B.seq nd.p2/V6LC_2_2_14_C.seq nd.p2/rdisc.pm - adapt for routers test - add to configure CurHopLimit pmtu.p2/CommonPMTU.pm - change to ignore the contents of Echo Request and check the only payload length of Echo Request for v6LC.4.1.10 and v6LC.4.1.11. 2004/11/18 Yukiyo.Akisada@jp.yokogawa.com fix typo in INSTALL.ct 2004/11/16 Release 1.1.1 Official release 2004/11/16 Hiroki.Endou@jp.yokogawa.com nd.p2/V6LC_2_1_6_A.seq nd.p2/V6LC_2_1_6_B.seq - change to check RetransTimer interval pmtu.p2/checkIncreasePMTU.seq - change to transmit NA in response to NS from NUT 2004/11/12 Release 1.1 Official release 2004/11/11 Hiroki.Endou@jp.yokogawa.com config.txt configure.pl - add to check the advanced functionalities support icmp.p2/Echo_Request_Link-Locals.seq pmtu.p2/Makefile.test pmtu.p2/mcastOne.seq pmtu.p2/mcastTwo.seq - change to check the advanced functionalitiy (transmitting Echo Requests or can not set packet size) support spec.p2/Makefile.test spec.p2/HHO_MSB10mc_EN.seq spec.p2/HHO_MSB11mc_EN.seq spec.p2/HHO_MSB10mc_IN.seq spec.p2/HHO_MSB11mc_IN.seq icmp.p2/Makefile.test icmp.p2/To_Multi_Pkt_Too_Big.seq - change to check the advanced functionality (multicast routing) support icmp.p2/Pkt_Too_Big.seq icmp.p2/To_Multi_Pkt_Too_Big.seq icmp.p2/Err_Condition_Too_Big.seq - change to check the advanced functionality (MTU configuration) support bin/mkph2.sh - change to check out config.txt configure.pl icmp.p2/INDEX_P2_router - correct test title 2004/10/20 Release 1.0.1 Official release 2004/10/12 Yukiyo.Akisada@jp.yokogawa.com spec.p2/IP_NH_Unexpected.def: - correct pointer in parameter problem nd.p2/V6LC_2_1_1_D.{seq,def}: - correct test sequence for host nd.p2/common.pm nd.p2/common_tn_ns.def nd.p2/common_tr1_na.def nd.p2/common_tr1_ns.def nd.p2/common_tr2_ns.def: - change to accept NS wich has source address using different address scope 2004/10/01 Release 1.0 1st official release [end of CHANGELOG]