NAME

CN_PingAfterIncorrectBu - Ping after No Home Address Option

TARGET

Host and Router

SYNOPSIS

CN_PingAfterIncorrectBu.seq [-tooloption ...] -pkt CN_PingAfterIncorrectBu.def

-tooloption: v6eval tool option

TOPOLOGY

                                                      MN'
                                                      |
                                      --------+-------+------- LinkY
                                              |
                                              R2      MN
                                              |       |
Link1 --------+-------        --------+-------+-------+------- LinkX
              |                       |
             NUT                      R1
              |                       |
Link0 --------+-----------------------+-----------------------

Link0	3ffe:501:ffff:100::/64
Link1	3ffe:501:ffff:101::/64
LinkX	3ffe:501:ffff:102::/64	home link
LinkY	3ffe:501:ffff:103::/64	foreign link
R1(Link0)	3ffe:501:ffff:100:200:ff:fe00:a0a0
MN	3ffe:501:ffff:102:200:ff:fe00:000b	home address
MN'	3ffe:501:ffff:103:200:ff:fe00:000b	care-of address

TEST PROCEDURE

       NUT      R1      MN      MN'
        |       |       |       |
        | <---- |       |       | RA
        |       |       |       |
        | <-------------------- | Echo Request
        | ----> |       |       | NS
        | <---- |       |       | NA
        | --------------------> | Echo Reply (*1)
        |       |       |       |
        | <---- |       |       | NA
        |       |       |       |
        | <-------------------- | Binding Update (no Home Address Option)
        |       |       |       |
        | <-------------------- | Echo Request (Home Address Option)
        | ------------> |       | Echo Reply (*2)
        |       |       |       |

1. check routing table - LinkY
	1.1. Host
		1.1.1. R1 sends RA
		1.1.2. MN' sends Echo Request
		1.2.3. Wait Echo Reply
		1.1.4. Receive Echo Reply

	1.2. Router
		1.2.1. MN' sends Echo Request
		1.2.2. Wait Echo Reply or NS
		1.2.3. If NS received then send NA, and wait Echo Reply again
		1.2.4. Receive Echo Reply

2. overwrite NCE on NUT
	2.1. R1 sends NA

3. check Binding Cache entry operation
	3.1. MN' sends incorrect Binding Update
	3.2. MN' sends Echo Request including Home Address Option
	3.3. Wait Echo Reply
	3.4. Receive Echo Reply

JUDGEMENT

(*1) PASS: MN' receives Echo Reply

(*2) PASS: MN receives Echo Reply including Routing Header

REFERENCE

<draft-ietf-mobileip-ipv6-15.txt>

8.2. Receiving Binding Updates

   Before accepting a Binding Update option received in any packet, the
   receiving node MUST validate the Binding Update according to the
   following tests:

    -  The packet meets the specific authentication requirements for
       Binding Updates, defined in Section 4.4.

    -  The packet MUST contain a Home Address option.

    -  The Option Length field in the Binding Update option is greater
       than or equal to the length specified in Section 5.1.

    -  The Sequence Number field in the Binding Update option is greater
       than the Sequence Number received in the previous Binding Update
       for this home address, if any.  As noted in Section 4.6, this
       Sequence Number comparison MUST be performed modulo 2**8.

   If the mobile node sends a sequence number which is not greater than
   the sequence number from the last successful Binding Update, then the
   receiving node MUST send back a Binding Acknowledgement with status
   code 141, and the last accepted sequence number in the Sequence
   Number field of the Binding Acknowledgement.

   Any Binding Update which fails to satisfy all of these tests for any
   other reason (than insufficiency of the Sequence Number) MUST be
   silently ignored, and the packet carrying the Binding Update MUST be
   discarded.

CN_Common.def