Hi,
> I'll have a look at it. I know that these warnings should be dealt with,
> but I don't know how.
The details of the test should confirm test specification (test ID.html).
A test result should confirm log or dump. If you have a question in the
details of a test, please show and ask the point.
> I had plans to test only host mode. But I gave it a try and ended with
> internal error.
For mipv6-ha and mipv6-mn.
I found the cause. Please modify the following files.
/usr/local/v6eval/include/std.def
---
//=======================================================================
// Other include files
// Standard Address definition
#include <stdaddr.def>
// Standard Packet definition
#include <stdpacket.def>
// Standard Const Variable definitions
#include <stdconst.def>
// #include <ike.def> <<<<<<<<<< you have to comment out
//=======================================================================
---
This line is not in an original file.
Isn't it modified?
> I sent new mipv6-ha in attachment.
>
> Doesn't it fail because all settings are set as false?
>
> Also, mipv6-ha readme suggests to use host as Type in nut.def
Where is it?
It seems that there is no description in mipv6-ha/00README_ha.txt.
INSTALL has the following description.
---
3.4. /usr/local/v6eval/etc/nut.def
You can copy both "System" and "TargetName" from the sample file
/usr/local/v6eval/etc/nut.def.sample.
"HostName" entry SHOULD be a host name of NUT.
"Type" entry MUST be:
- "host" if NUT is configured as a host.
- "router" if NUT is configured as a router.
---
Best Regards
--
Kiyoaki Kawaguchi
"Vit Pelcak <vpelcak@suse.cz>" wrote:
> This is a multi-part message in MIME format.
>
> K.Kawaguchi napsal(a):
> > Hi,
> >
> > mipv6-cn
> > Almost good.
> > You should note some warinig in result, if you will get the IPv6 Ready Logo.
> > IPv6 Ready Logo requests 100% pass except skips.
> >
>
> I'll have a look at it. I know that these warnings should be dealt with,
> but I don't know how.
>
> > mipv6-ha
> > You should configure the file /usr/local/v6eval/etc/nut.def.
> > ---
> > # Type
> > # host, router, special
> > Type router <<< change
> > ---
> >
>
> I had plans to test only host mode. But I gave it a try and ended with
> internal error.
>
> ===> mipv6-ha
> (clean)
>
> rm -f INDEX INDEX_PHASE2
> INDEX_PHASE2_FINE_GRAIN index.html
> report.html summary.html
> [0-9]*.html *.dump
> *.log *.tmp
> *.bak ipsec_sa.pl
> config.pm config.def
> sequence.def ikesub.def
> pod2htmd* pod2htmi*
> *.rtadvd.conf local_haad_reply.def
> local_ra_deregistration.def
> local_ra_registration.def
>
> ===>
> mipv6-ha
>
> /usr/local/v6eval/bin/autorun -F -tiny -title="Conformance Test for
> Home Agent"
> ./INDEX
>
> ========== TEST 1
> ==========
>
> ./HA_0_0_0.seq -pkt ./HA_0_0_0.def -log 1.html -ti "HA_0_0_0 -
> Initialization and general
> configuration"
>
> CONFIGURATION
>
>
> .
> .
> .
>
> INITIALIZATION
> Start Capturing Packets (Link0)
> calculate RUT and MN addresses
> Clear Captured Packets (Link0)
> "/usr/local/v6eval//include/ike.def", line 74: error: IKE_EH_NUTtoTN
> duplicated declaration near 'Hdr_Ether IKE_EH_NUTtoTN { '
> "/usr/local/v6eval//include/ike.def", line 77: error: IKE_RECV
> duplicated declaration near 'Frame_Ether IKE_RECV { '
> "/usr/local/v6eval//include/ike.def", line 77: error:
> _PACKET_IPV6_IKE_RECV duplicated declaration near 'Frame_Ether IKE_RECV
> { header=IKE_EH_NUTtoTN; packet=_PACKET_IPV6_IKE_RECV; } Packet_IPv6
> _PACKET_IPV6_IKE_RECV {h'
> "/usr/local/v6eval//include/ike.def", line 77: error: _HDR_IPV6_IKE_RECV
> duplicated declaration near 'Frame_Ether IKE_RECV {
> header=IKE_EH_NUTtoTN; packet=_PACKET_IPV6_IKE_RECV; } Packet_IPv6
> _PACKET_IPV6_IKE_RECV
> {header=_HDR_IPV6_IKE_RECV;upper=_UPP_UDP_IKE_RECV;} Hdr_IPv6
> _HDR_IPV6_IKE_RECV { '
> "/usr/local/v6eval//include/ike.def", line 77: error: _UPP_UDP_IKE_RECV
> duplicated declaration near 'Frame_Ether IKE_RECV {
> header=IKE_EH_NUTtoTN; packet=_PACKET_IPV6_IKE_RECV; } Packet_IPv6
> _PACKET_IPV6_IKE_RECV
> {header=_HDR_IPV6_IKE_RECV;upper=_UPP_UDP_IKE_RECV;} Hdr_IPv6
> _HDR_IPV6_IKE_RECV { Version = auto; TrafficClass = auto; FlowLabel =
> auto; PayloadLength = auto; NextHeader = auto; HopLimit = any;
> SourceAddress = any; DestinationAddress = any; } Upp_UDP
> _UPP_UDP_IKE_RECV { '
> "/usr/local/v6eval//include/ike.def", line 77: error: _HDR_UDP_IKE_RECV
> duplicated declaration near 'Frame_Ether IKE_RECV {
> header=IKE_EH_NUTtoTN; packet=_PACKET_IPV6_IKE_RECV; } Packet_IPv6
> _PACKET_IPV6_IKE_RECV
> {header=_HDR_IPV6_IKE_RECV;upper=_UPP_UDP_IKE_RECV;} Hdr_IPv6
> _HDR_IPV6_IKE_RECV { Version = auto; TrafficClass = auto; FlowLabel =
> auto; PayloadLength = auto; NextHeader = auto; HopLimit = any;
> SourceAddress = any; DestinationAddress = any; } Upp_UDP
> _UPP_UDP_IKE_RECV { header = _HDR_UDP_IKE_RECV; payload =
> IKE_RECV_ISAKMP; } Hdr_UDP _HDR_UDP_IKE_RECV { '
> "/usr/local/v6eval//include/ike.def", line 100: error: IKE_RECV_ISAKMP
> duplicated declaration near 'Udp_ISAKMP IKE_RECV_ISAKMP {
> "/usr/local/v6eval//include/ike.def", line 105: error:
> IKE_RECV_ISAKMP_HDR duplicated declaration near 'Hdr_ISAKMP
> IKE_RECV_ISAKMP_HDR {
> V6evalTool.pm vSend() return status=1
> Died at /usr/local/lib/perl5/site_perl/5.8.8/V6evalTool.pm line 2578.
> -> internal error
>
> I sent new mipv6-ha in attachment.
>
> Doesn't it fail because all settings are set as false?
>
> Also, mipv6-ha readme suggests to use host as Type in nut.def
>
> > mipv6-mn
> > I am sorry. A cause is still unknown. I still need information.
> > Which version of FreeBSD are you using?
> > Please send the derectory "/usr/local/v6eval/include".
> >
>
> OK. In attachment.
>
> I use FreeBSD 7.0 as TN and openSUSE 11.1 as NUT.
>
> Thank you for help.
>
> Regards
>
> Vit Pelcak
>
>
>
>
>
>
>